HTL 225/230…240
Product family benefits
- Very low power loss thanks to high efficacy
- Through-wiring possible on the primary side
- Large temperature range
- Protective operation throughout the entire partial-load range for long lamp life
- High efficiency
Areas of application
- Effect and accent lighting
- Living rooms
- Object lighting
- Conference rooms
- Restaurants
- Recessed and surface-mounted furniture luminaires
- Shop lighting
- Event rooms
Technical Data
Electrical data
Lamp wattage
50…225 W
Maximum output power
225 W
Line current
0.90 A
Input voltage DC
176…275 V
Nominal voltage
230…240 V
Power factor λ
0.95
Operating frequency
50 kHz
Nominal output voltage
11.6 / 11.7 V
Input voltage AC
207…264 V
Mains frequency
50…60 Hz
System wattage
230.00 W
Efficiency in full-load
94 %
Input voltage range
230…240 V
Max. ECG no. on circuit breaker 10 A (B)
11
Galvanic isolation primary/secondary
4.00 kV
Max. ECG no. on circuit breaker 16 A (B)
18
Inrush current
1.5 A
Dimensions & weight
Length
170.0 mm
Width
44.0 mm
Height
34.0 mm
Cable cross-section, input side
2.5 mm²
Cable cross-section, output side
4.0 mm²
Wire preparation length, input side
14 / 8.0 mm
Wire preparation length, output side
14 / 8.0 mm
Mounting hole spacing, length
140.0 mm
Product weight
225.00 g
Temperatures & operating conditions
Ambient temperature range
-20…+50 °C
Maximum temperature at tc test point
80 °C
Additional product data
Design / version
Long with cable clamp
Capabilities
Dimming method
Trailing- or leading-edge phase control for inductive load dimmers
Overload protection
Automatic switch off, reversible
Overheating protection
Automatic switch off, reversible
Short-circuit protection
Automatic switch-off, reversible
Max. cable length to lamp/LED module
2.0 m
Cable/wire types, input side
H03VV-F 2x0.50 / H03VV-F 2x0.75 / H03VVH2-F 2x0.75 / H05VVH2-F 2x0.75 / H05VV-F 2x2.5 / NYM-O 2x1.5 / NYM-J 3x1.5 mm²
Cable/wire types, output side
H03VV-F 2x0.75 / H05VVH2-F 2x0.75 / H05VV-F 2x1.5 / H05VV-F 2x2.5 / NYM-O 2x1.5 / NYM-J 3x1.5 / NYM-J 3x2.5 mm²
Dimmable
Yes
Dimming range
0…100 %
No-load proof
Yes
Suitable for fixtures with prot. class
II
Intended for no-load operation
No
Certificates & standards
Approval marks – approval
ENEC 10 / VDE / VDE-EMC / EAC
Standards
Acc. to EN 61347/Acc. to EN 55015/Acc. to EN 61000-3-2/Acc. to EN 61547/Acc. to EN 61047
Type of protection
IP20
Logistical data
Commodity code
85044095900
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
19-05-2023
Primary Article Identifier
4008321927026
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
990a7236-e5d3-4aac-ae15-373eb0cf86b7
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4008321927026 |
UNV
| 1 | 170mm x 44mm x 34mm | 225.00g | 0.25dm³ |
| 4008321927040 |
VS
| 10 | 235mm x 183mm x 89mm | 2361.00g | 3.83dm³ |
Downloads
Data sheets
Information about Family
HALOTRONIC PROFESSIONAL HTL is an electronic transformer, dimmable on the leading and trailing edge. It protects from short-circuit, overtemperature and overload (electronically reversible) and has electrical isolation between the primary and secondary sides. Switching between the electronic transformer and the lamp is not permitted. With high levels of energy efficiency, this transformer has many applications, but is particularly good for effect and accent lighting, object lighting and furniture luminaires (recessed and surface-mounted). It is also good for living rooms, conference and event rooms, shoplighting and restaurant lighting. High efficacy means that little power is lost, and HALOTRONIC PROFESSIONAL HTL covers a large temperature range. Protective operation throughout the partial-load range prolongs lamp life, and you can through-wire on the primary side.
Product family features
- Line frequency: 50…60 Hz
- RI suppression: to EN 55015 (A1: 2007)/CISPR 15, EN 55022
- Line harmonics according to EN 61000-3-2
- Immunity according to EN 61547
- Safety: to EN 61347
- Short-circuit protection, overload protection, overtemperature protection: electronically reversible
- Electrical isolation between the primary side and the secondary side
- Dimmable on the leading edge and trailing edge
Ecodesign regulation information:
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
HTL 105/230…240
|
230…240 V | Yes | 34.0 mm | 44.0 mm | 35…105 W | ||
|
|
HTL 225/230…240
|
230…240 V | Yes | 34.0 mm | 44.0 mm | 50…225 W |