OT FIT 40/220…240/1A0 CS

Product family benefits
  • Higher quality of light thanks to low output ripple current
  • High flexibility due to four different output currents
  • Small housing for flexible luminaire designs
  • High efficiency
Areas of application
  • Suitable for downlights, spotlights and LED panels
  • Suitable for luminaires of protection classes I and II
German innovation awards 2019 winner

Technical Data

Electrical data

Nominal input voltage

220…240 V

Mains frequency

50/60 Hz

Input voltage AC

198…264 V

Total harmonic distortion

< 10 %

At full load, 230 V, 50 Hz / see graphs

Power factor λ

0.98

Efficiency in full-load

90 %

at 230 V, 50 Hz

Device power loss

4.9 W

At 230 V, Input power 49 W max.

Protective conductor current

<0.7 mA

Inrush current

≤ 35 A

twidth = 200 µs (measured at 50 % Ipeak)

Max. ECG no. on circuit breaker 10 A (C)

19

Max. ECG no. on circuit breaker 10 A (B)

11

Max. ECG no. on circuit breaker 16 A (B)

19

Max. ECG no. on circuit breaker 16 A (C)

31

Max. ECG no. on circuit breaker 25 A (B)

29

Surge capability (L/N-Ground)

2 kV

Surge capability (L-N)

1 kV

Nominal output voltage

25…42 / 30…42 V

30 - 42V @ 1050 mA

U-OUT (working voltage)

60 V

Nominal output current

800 / 900 / 950 / 1050 mA

Output current tolerance

±7.5 %

Default output current

1050 mA

Output ripple current (100 Hz)

< 5 %

Output PSTLM

≤1

Output SVM

≤0.4

Nominal output power

20…44.1 W

Maximum output power

44.1 W

Galvanic isolation

SELV

Galvanic isolation primary/secondary

SELV

Current set

DipSwitch

Dimensions & weight

Mounting hole spacing, length

88.0 mm

Mounting hole spacing, width

34.0 mm

Product weight

110.00 g

Cable cross-section, input side

0.5…1.5 mm²

Cable cross-section, output side

0.5…1.5 mm²

Wire preparation length, input side

7…8 mm

Wire preparation length, output side

7…8 mm

Length

97.0 mm

Height

29.5 mm

Width

43.0 mm

Colors & materials

Casing material

Plastic

Temperatures & operating conditions

Ambient temperature range

-20…+50 °C

Maximum temperature at tc test point

80 °C

Max.housing temperature in case of fault

110 °C

Temperature range at storage

-20…80 °C

Permitted rel. humidity during operation

5…85 %

Non-condensing

Lifespan

ECG lifetime

50000 h

At maximum Tc = 80°C / 10% failure rate

Additional product data

Predecessor EAN

4052899435650

Capabilities

Dimmable

No

Overheating protection

Automatic reversible

Overload protection

Automatic reversible

Short-circuit protection

Automatic reversible

No-load proof

Yes

Intended for no-load operation

No

Max. cable length to lamp/LED module

2.0 m

Output wires must be routed as close as possible to each other

Suitable for fixtures with prot. class

I / II

Type of connection, input side

Push terminal

Type of connection, output side

Push terminal

Detection angle (PIR)

-

Number of channels

1

Suitable for through-wiring

No

Control interface

-

Detection angle (Light sensor)

-

Programming

Programming device

DIPswitch

Certificates & standards

Approval marks – approval

CCC / CE / RCM / ENEC 05

Standards

Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547

Type of protection

IP20

Protection class

I,II

Logistical data

Commodity code

85044083900

Environmental information


Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)

Date of Declaration

26-05-2023

Primary Article Identifier

4052899617339

Candidate List Substance 1

Lead

CAS No. of substance 1

7439-92-1

Safe Use Instruction

The identification of the Candidate List substance is sufficient to allow safe use of the article.

Declaration No. in SCIP database

06ee480d-1593-42d1-9ca2-8009fd63d4df

Packaging information

EAN

Unit

Piece

Dimension l x w x h

Weight

Volume

4052899617339 UNV

Unpacked

1
4052899617797 VS

Shipping box

20 228mm x 208mm x 78mm 2403.00g 3.70dm³

Downloads

Accessories optional

Information about Family

Product family features
  • Lifetime: up to 50,000 h (temperature at max. tc )
  • Cable clamp kit for independent mounting
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.

Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.

Products

Sort by:
Product
Nominal output voltage
Nominal output current
Length
Width
Height
Data sheet
OT FIT 20/220…240/500 CS
23…42 V 250 / 350 / 450 / 500 mA 97.0 mm 43.0 mm 29.5 mm
OT FIT 30/220…240/700 CS
23…42 V 500 / 600 / 650 / 700 mA 97.0 mm 43.0 mm 29.5 mm
OT FIT 40/220…240/1A0 CS
25…42 / 30…42 V 800 / 900 / 950 / 1050 mA 97.0 mm 43.0 mm 29.5 mm