OTi DALI 10/220…240/700 NFC
Product family benefits
- Versatile DALI window driver due to flexible output characteristic
- Very high efficiency
- Protection of the system thanks to thermal management and Smart Control
- High-quality dimming of 1…100 % by amplitude dimming
- Easy and fast output current setting via NFC
- Suitable for emergency Installations (acc. to EN 60598-2-22 and IEC 61347-2-13,appendix J) thanks to DC detection (0 Hz, pulsating DC), on/off switchable
- Feedback of power consumption and operating hours (Fit for SMART GRID)
- Suitable for buildings according to EPBD/BREEAM/LEED due to automatic Constant Lumen Output setting
Areas of application
- Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
- Suitable for use in luminaires with flexible current setting
- Suitable for indoor SELV installations
- Suitable for luminaires of protection classes I and II
- Suitable for downlights, spotlights and LED panels
- Installation via Cable Clamp Kit possible (depending on version of product)
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
0/50/60 Hz
Input voltage AC
198…264 V
Input voltage DC
176…276 V
Total harmonic distortion
15 %
Power factor λ
> 098/> 094
Efficiency in full-load
82 %
Device power loss
3.5 W
Inrush current
< 5 A
Max. ECG no. on circuit breaker 10 A (B)
80
Max. ECG no. on circuit breaker 16 A (B)
130
Max. ECG no. on circuit breaker 25 A (B)
-
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
2.5…45 V
U-OUT (working voltage)
60 V
Nominal output current
150…700 mA
Default output current
350 mA
Output current tolerance
±3 %
Output ripple current (100 Hz)
< 2 %
Output PSTLM
≤1
Output SVM
≤0.4
Nominal output power
10 W
Maximum output power
10 W
Galvanic isolation primary/secondary
SELV
Networked standby power
≤0.15 W
Galvanic isolation DALI/output
SELV
Galvanic isolation DALI/mains
Basic
Power loss in stand-by mode
≤0.15 W
Current set
DALI / NFC
Dimensions & weight
Mounting hole spacing, length
115.0 mm
Product weight
5800 g
Cable cross-section, input side
0.2…1.5 mm²
Cable cross-section, output side
0.2…1.5 mm²
Wire preparation length, input side
8.0…9.1 mm
Wire preparation length, output side
8.0…9.1 mm
Length
1240 mm
Height
210 mm
Width
310 mm
Colors & materials
Casing material
Plastic
Temperatures & operating conditions
Ambient temperature range
-20…+50 °C
Maximum temperature at tc test point
75 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-40…+85 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 / 100000 h
Additional product data
Successor EAN
4062172143899
Capabilities
Dimmable
Yes
Dimming interface
DALI-2
Dimming range
1…100 %
Dimming method
Amplitude Modulation
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Intended for no-load operation
No
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I / II
Type of connection, input side
Push terminal
Type of connection, output side
Push terminal
Constant lumen function
Programmable
Number of channels
1
Suitable for emergency lighting
Yes
Programming interface
DALI, NFC
Programming
Tuner4TRONIC
Yes
Programming device
DALI / NFC
Tuner4TRONIC Field App
Yes
Programmable features
Constant Lumen
Yes
Lamp Operating Time
Yes
Driver Guard
Yes
DALI Settings
Yes
Emergency Mode
Yes
Configuration Lock
Yes
Soft Switch Off
Yes
Dim to Dark
Yes
TouchDIM + Sensor
No
Corridor Functionality
No
OEM Key
No
Certificates & standards
Approval marks – approval
ENEC 10 / VDE / EMC / EL / CE / DALI-2 / CCC
Standards
Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 55015/Acc. to EN 61547/Acc. to EN 61000-3-2/Acc. to EN 62384/Acc. to EN 62386/Acc. to IEC 62386-101:Ed2/Acc. to IEC 62386-102:Ed2/Acc. to IEC 62386-207:Ed1
Protection class
II
Type of protection
IP20
Logistical data
Commodity code
850440829000
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
18-10-2022
Primary Article Identifier
4052899562639
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
76aba481-9f21-42ba-9d2e-a3a03dbf7947
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4052899562639 |
UNV
| 1 | 124mm x 31mm x 21mm | 58.00g | 0.08dm³ |
| 4052899562646 |
VS
| 20 | 165mm x 258mm x 71mm | 1416.00g | 3.02dm³ |
Downloads
Data sheets
Accessories optional
Information about Family
Peace of mind – Freedom in design & usage.
This Compact LED Driver is fully digitally programmable by DALI, NFC and LT2 and includes 1…100% dimming. The very wide operating window and an optional cable clamp for independent installation and through-looping allow some flexibility in its usage.
This Compact LED Driver is fully digitally programmable by DALI, NFC and LT2 and includes 1…100% dimming. The very wide operating window and an optional cable clamp for independent installation and through-looping allow some flexibility in its usage.
Product family features
- Supply voltage: 220…240 V
- Line frequency: 0 Hz | 50 Hz | 60 Hz
- Line voltage: 198…264 V
- According to EN 61347-1, 61347-2-13, 62384
- RI suppression: to EN 55015/CISPR 15
- Line harmonics according to EN 61000-3-2
- Immunity according to EN 61547
- Lifetime: up to 100,000 h
- Type of protection: IP20
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
|
OTi DALI 10/220…240/700 NFC
|
2.5…45 V | 150…700 mA | 1240 mm | 310 mm | 210 mm | ||
|
OTi DALI 25/220…240/700 LT2 NFC
|
12…54 V | 180…700 mA | 1030 mm | 670 mm | 295 mm | ||
|
OTi DALI 50/220...240/1A4 LT2 FAN NFC
|
15…54 V | 600…1400 mA | 1100 mm | 750 mm | 250 mm |