OT FIT 10/220-240/255 TW
Product family benefits
- Compatible with the most common leading-edge and trailing-edge phase dimmers
- Flexible current setting (DIPswitch – 2 to 4 currents)
- Flicker-free dimming
- Higher quality of light thanks to < 5% output ripple current
- Housing from 80% recycled plastic
Areas of application
- Decorative illumination
- Downlights, flat luminaires
- Hospitality
- Living areas
- Museums, residential buildings
- Offices
- Shop lighting
- Suitable for indoor SELV installations
- Suitable for luminaires of protection class I and II
Technical Data
Electrical data
Nominal input voltage
220…240 V
Mains frequency
50…60 Hz
Input voltage AC
198…264 V
Total harmonic distortion
< 20 %
Power factor λ
> 0.90
Device power loss
2.2 W
Inrush current
< 5 A
Max. ECG no. on circuit breaker 10 A (C)
74
Max. ECG no. on circuit breaker 10 A (B)
74
Max. ECG no. on circuit breaker 16 A (B)
118
Max. ECG no. on circuit breaker 16 A (C)
118
Max. ECG no. on circuit breaker 25 A (B)
-
Surge capability (L/N-Ground)
2 kV
Surge capability (L-N)
1 kV
Nominal output voltage
27…38 V
U-OUT (working voltage)
60 V
Nominal output current
180 / 205 / 230 / 255 mA
Output current tolerance
±10 %
Output ripple current (100 Hz)
< 20 %
Nominal output power
9.7 W
Power loss in stand-by mode
<1 W
Galvanic isolation primary/secondary
SELV
Current set
DipSwitch
Dimensions & weight
Product weight
80.00 g
Cable cross-section, input side
0.75 mm²
Cable cross-section, output side
0.5 mm²
Wire preparation length, input side
9.0…10.0 mm
Wire preparation length, output side
9.0…10.0 mm
Length
102.0 mm
Height
22.0 mm
Width
51.0 mm
Colors & materials
Casing material
Plastic
Temperatures & operating conditions
Ambient temperature range
-20…+50 °C
Maximum temperature at tc test point
70 °C
Max.housing temperature in case of fault
110 °C
Temperature range at storage
-20…80 °C
Permitted rel. humidity during operation
5…85 %
Lifespan
ECG lifetime
50000 h
Capabilities
Dimmable
Yes
Dimming interface
Phase Cut
Dimming range
3…100 %
Dimming method
Trailing-edge phase dimmer
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Max. cable length to lamp/LED module
2.0 m
Suitable for fixtures with prot. class
I / II
Type of connection, input side
Wago 744 or equivalent
Number of channels
2
Programming
Programming device
DIPswitch
Certificates & standards
Approval marks – approval
CCC
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
Protection class
II
Type of protection
IP20
Logistical data
Commodity code
850440829000
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
21-09-2022
Primary Article Identifier
4062172080569
Candidate List Substance 1
Lead
CAS No. of substance 1
7439-92-1
Safe Use Instruction
The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database
480fe194-4939-4b30-b754-1dd1fae03f3a
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
|---|---|---|---|---|---|
| 4062172080569 |
UNV
| 1 | |||
| 4062172080576 |
VS
| 20 | 267mm x 216mm x 64mm | 1729.00g | 3.69dm³ |
Downloads
Data sheets
Information about Family
Constant Current SELV drivers with leading- or trailing-edge dimming.
The compatibility with the most common leading-edge and trailing-edge phase dimmers and the possibility of dimming from 5-100% marks one of the key characteristics. Others include a cable clamp for independent installations and DIP switsches for 4 output currents per wattage.
The compatibility with the most common leading-edge and trailing-edge phase dimmers and the possibility of dimming from 5-100% marks one of the key characteristics. Others include a cable clamp for independent installations and DIP switsches for 4 output currents per wattage.
Product family features
- Cable clamp housing for independent mounting
- Dimmable on the leading edge and trailing edge
- Housing for independent installation
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
| Product |
|
|
|
|
|
Data sheet | ||
|---|---|---|---|---|---|---|---|---|
|
OT FIT 7/220...240/180 CS PC
|
27…40 V | 100 / 120 / 155 / 180 mA | 130.0 mm | 30.0 mm | 22.2 mm | ||
|
OT FIT 8/220...240/180 CS PC
|
27…40 V | 100 / 120 / 155 / 180 mA | 95.0 mm | 50.0 mm | 22.0 mm | ||
|
OT FIT 18/220...240/450 CS PC
|
27…40 V | 225 / 325 / 350 / 450 mA | 95.0 mm | 50.0 mm | 22.0 mm | ||
|
OT FIT 30/220…240/700 CS PC
|
27…40 V | 500 / 700 mA | 95.0 mm | 53.0 mm | 30.0 mm | ||
|
OT FIT 40/220...240/1A0 CS PC
|
27…40 V | 800 / 900 / 950 / 1050 mA | 108.0 mm | 67.0 mm | 22.0 mm | ||
|
|
OT FIT 10/220-240/255 TW
|
27…38 V | 180 / 205 / 230 / 255 mA | 102.0 mm | 51.0 mm | 22.0 mm | ||
|
OT FIT 18/220–240/450 TW
|
27…38 V | 300 / 350 / 400 / 450 mA | 95.0 mm | 53.0 mm | 30.0 mm | ||
|
OT FIT 40/220–240/1A0 TW
|
27…38 V | 700 / 800 / 900 / 1000 mA | 108.0 mm | 67.0 mm | 22.0 mm |