PT-FIT 70/220…240 I

Product family benefits
  • ECG with ergonomic strain relief for correct installation in suspended ceilings
  • Optimized cost/benefit factor
  • Automatic safety shutdown of lamps in the event of a defect or at end of life (EoL)
Areas of application
  • Shop lighting
  • Health and fitness areas (in luminaires with protection class IP66 or higher)
  • Effect and accent lighting

Safety advice
Ballast losses and lamp heat radiation can lead to heat accumulation in a completely closed case. Therefore it is necessary to ensure that the temperature at the measuring point t of the ECG does not exceed the maximum value.
Attention!
For safety reasons disconnect the device before replacing the lamp!

Technical Data

Electrical data

Lamp wattage

73 W

Maximum output power

73 W

Line current

0.36 A

At 230 VAC

Ignition voltage

4.5 kVp

Operating frequency

0.200…0.240 kHz

System wattage

80.00 W

Efficiency in full-load

92 %

Input voltage AC

198…264 V

Nominal voltage

220…240 V

Mains frequency

50…60 Hz

Power factor λ

0.95

Minimum

Inrush current

45 A

twidth = 250 µs (measured at 50 % Ipeak)

Max. ECG no. on circuit breaker 10 A (B)

7

Type B

Max. ECG no. on circuit breaker 16 A (B)

13

Type B

Max. no. of ECGs on 16A MCB with EBN-OS

32

Type B

Protective conductor current

0.3 mA

U-OUT (working voltage)

250 V

Max. working voltage between LH and LL

250 V

Max. working voltage betw. LL/LH & earth

250 V

Max. capacitance of wire ECG/lamp

120 pF

Dimensions & weight

Length

172.0 mm

Width

83.0 mm

Height

33.0 mm

Mounting hole spacing, length

163.0 mm

Cable cross-section, input side

0.75…1.5 / 0.75…2.5 mm²

With ferrule / Without ferrule

Cable cross-section, output side

0.75…1.5 / 0.75…2.5 mm²

With ferrule / Without ferrule

Wire preparation length, input side

5.5…6.5 mm

Wire preparation length, output side

5.5…6.5 mm

Product weight

290.00 g

Colors & materials

Casing material

Plastic

Temperatures & operating conditions

Ambient temperature range

-15…+45 °C

Maximum temperature at tc test point

75 °C

Lifespan

ECG lifetime

30000 h

At maximum Tc / 10% failure rate

Additional product data

Design / version

With cable clamp

Suitable for lamp power (1 lamp)

70 W

Capabilities

Max. cable length to lamp/LED module

1.5 m

Overheating protection

Power reduction and switch off at T > 75 °C at the tc point

ECG reset time

> 0.5 s

Cable/wire types, input side

NYM-J 3x1.5 / NYM-J 3x2.5 / H05VV-F 3x1.5 / NHXMH-J 3x1.5 mm²

Cable/wire types, output side

SIHF-J 3x1.5 / SIHF-J 3x2.5 / SIHSI 3x1.0 mm²

Dimmable

No

Restriction on ignition time

20 min

Suitable for fixtures with prot. class

I

Intended for no-load operation

No

Certificates & standards

Approval marks – approval

VDE / VDE-EMC / EAC / C-Tick

Type of protection

IP20

EEI – Energy Label

A2

Standards

Acc. to EN 61347-2-12/Acc. to EN 55015/Acc. to EN 61000-3-2/Acc. to EN 61547/Acc. to EN 62493

Logistical data

Commodity code

85041080900

Environmental information


Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)

Date of Declaration

26-05-2023

Primary Article Identifier

4008321377685

Candidate List Substance 1

Lead

CAS No. of substance 1

7439-92-1

Safe Use Instruction

The identification of the Candidate List substance is sufficient to allow safe use of the article.

Declaration No. in SCIP database

620a8fbb-fa0f-4f92-af4e-bc7e7d31b826

Packaging information

EAN

Unit

Piece

Dimension l x w x h

Weight

Volume

4008321377685 UNV

Unpacked

1 171mm x 83mm x 32mm 270.00g 0.45dm³
4008321377692 VS

Shipping box

20 430mm x 368mm x 91mm 5897.00g 14.40dm³

Downloads

Information about Family

POWERTRONIC PT-FIT I is an electronic control gear (ECG) for use with high intensity discharge lamps, and comes with ergonomic strain relief for correct installation in suspended ceilings. With an energy efficiency index of A2, it gives you an optimized cost/benefit balance and is great for use in shoplighting, health and fitness environments (as long as it is installed in a dry and corrosion-resistant area) and for creating effect and accent lighting. POWERTRONIC PT-FIT I also gives you the assurance of automatic lamp shutdown in the event of defect or end of life.
Product family features
  • Energy Efficiency Index EEI: A2
  • Supply voltage: 220…240 V
  • Line frequency: 50…60 Hz
  • RI suppression: to EN 55015/CISPR 15
  • Safety: to EN 61347-2-12
  • Line harmonics according to EN 61000-3-2
  • Immunity according to EN 61547
Ecodesign regulation information:
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.

Products

Sort by:
Product
Nominal voltage
Height
Length
Lamp wattage
Ignition voltage
Data sheet
PT-FIT 35/220…240 I
220…240 V 33.0 mm 172.0 mm 39 W 4.5 kVp
PT-FIT 70/220…240 I
220…240 V 33.0 mm 172.0 mm 73 W 4.5 kVp