OT 120/220 240/24 DIM P
Product family benefits
- Large range of products from 20 W to 250 W
- Installation in very cold and hot environments
- Very stable output power
- High electronical reversible short-circuit, overload, overtemperature protection
- Smart Power Supply: boosting power to turn on cold LEDs
- Independent installation possible
- Dimming range: 1 100 %
Areas of application
- Facades, public squares, cruise ships
- Signage
- Suitable for indoor and outdoor installations
Technical Data
Electrical data
Nominal input voltage
220 240 V
Mains frequency
50 60 Hz
Input voltage AC
198 264 V
Total harmonic distortion
< 20 %
Power factor λ
090/095
Device power loss
15.0 W
Inrush current
60 A
Max. ECG no. on circuit breaker 10 A (B)
6
Max. ECG no. on circuit breaker 16 A (B)
10
Max. ECG no. on circuit breaker 25 A (B)
17
Surge capability (L/N-Ground)
6 kV
Surge capability (L-N)
3 kV
Nominal output voltage
24 V
U-OUT (working voltage)
24 V
Nominal output power
120 W
Galvanic isolation
SELV
Galvanic isolation primary/secondary
3.75 kV
Dimensions & weight
Mounting hole spacing, length
241.0 mm
Mounting hole spacing, width
15.0 mm
Product weight
110000 g
Cable cross-section, input side
1.0 mm²
Cable cross-section, output side
1.5 mm²
Wire preparation length, input side
10 11 mm
Wire preparation length, output side
10 11 mm
Cable/wire length, control input
300 mm
Cable/wire length, input side
300 mm
Cable/wire length, output side
300 mm
Height
390 mm
Length
2500 mm
Width
600 mm
Colors & materials
Casing material
Metal
Temperatures & operating conditions
Ambient temperature range
-25 +55 °C
Maximum temperature at tc test point
80 °C
Max.housing temperature in case of fault
100 °C
Temperature range at storage
-40 +85 °C
Permitted rel. humidity during operation
5 85 %
Lifespan
ECG lifetime
50000 h
Additional product data
Successor EAN
4052899545885
Capabilities
Dimmable
Yes
Dimming interface
1 10 V
Dimming range
3 100 %
Dimming method
Pulse Width Modulation
Overheating protection
Automatic reversible
Overload protection
Automatic reversible
Short-circuit protection
Automatic reversible
No-load proof
Yes
Suitable for fixtures with prot. class
I
Type of connection, output side
Wires
Number of channels
1
Certificates & standards
Approval marks approval
CE / CB / RCM / EAC / ENEC 18 / BIS
Standards
Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3-2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
Protection class
I
Type of protection
IP67
Logistical data
Commodity code
850440829000
Environmental information
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration
11-10-2022
Primary Article Identifier
4008321981691
Declaration No. in SCIP database
In work
Packaging information
EAN |
Unit |
Piece |
Dimension l x w x h |
Weight |
Volume |
---|---|---|---|---|---|
4008321981691 |
FS
| 1 | 340mm x 100mm x 58mm | 1180.00g | 1.97dm³ |
4008321981752 |
VS
| 10 | 560mm x 400mm x 155mm | 13400.00g | 34.72dm³ |
Downloads
Information about Family
Free yourself to design and install optimized, innovative, unique lighting design and luminaires, even in tight and flat light fittings or in sites such as suspended ceilings, with your choice of compact constant voltage supply from the OPTOTRONIC OT 80/220
240/24 DIM P range of CV Power supplies 24 V with 1
10 V. Dimmable via a fully isolated 1
10 V interface, they are suitable for use in SELV installations both inside and outside and have an output power range of up to 240 W.
Product family features
- DC mode functionality
- Type of protection: IP66 and IP67
- Surge protection: up to 4 kV (L-N) / 6 kV (L/N-PE)
- Wide operating temperature range: -30 +55 °C
- Lifetime: up to 50,000 h (temperature at max. tc )
- Dimmable via fully isolated 1 10 V interface
Ecodesign regulation information:
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Intended for use with LED modules.
The forward voltage of the LED light source shall be within the defined operating window of the control gear in all operating conditions including dimming if applicable.
Separate control gear and light sources must be disposed of at certified disposal companies in accordance with Directive 2012/19/EU (WEEE) in the EU and with Waste Electrical and Electronic Equipment (WEEE) Regulations 2013 in the UK. For this purpose, collection points for recycling centres and take-back systems (CRSO) are available from retailers or private disposal companies, which accept separate control gear and light sources free of charge. In this way, raw materials are conserved and materials are recycled.
Products
Product |
|
|
|
|
|
Data sheet | ||
---|---|---|---|---|---|---|---|---|
OT 20/220
240/24 DIM P
|
20 W | Yes | 1780 mm | 430 mm | 250 mm | |||
OT 40/220
240/24 DIM P
|
40 W | Yes | 2080 mm | 430 mm | 260 mm | |||
OT 60/220
240/24 DIM P
|
60 W | Yes | 2080 mm | 430 mm | 260 mm | |||
OT 100/220
240/24 DIM P
|
100 W | Yes | 2400 mm | 500 mm | 340 mm | |||
OT 120/220
240/24 DIM P
|
120 W | Yes | 2500 mm | 600 mm | 390 mm | |||
OT 130/220
240/24 DIM P
|
130 W | Yes | 2200 mm | 630 mm | 370 mm | |||
OT 240/220
240/24 DIM P
|
240 W | Yes | 2500 mm | 800 mm | 390 mm | |||
OT 250/220
240/24 DIM P
|
250 W | Yes | 2650 mm | 680 mm | 400 mm |